Miter Saw Fix

One of my ear­li­est “nice” tools was a com­pound miter saw. I bought a “new“1 Ridgid 10″ miter saw about 15 years ago. It’s been pret­ty handy over the years, but I noticed last year (on my fin­ish­ing stor­age rack project) that the fence was bowed. As the blade would cut through he piece, the piece would then pinch into the blade. At best, that just ends up mess­ing up an oth­er­wise clean cut. But worse, it can be a bit dan­ger­ous any time a piece is pinched like that (at least with a miter saw, the blade is gen­er­al­ly pulling it down­ward into the sup­port). I searched for a replace­ment part, but those are no longer avail­able for this mod­el.

Thus it was time to just try to fix it. The fence is a very odd­ly shaped piece of alu­minum. I had to unthread the four hex bolts hold­ing it in place. They were pret­ty tight, to say the least.

I near­ly broke my Allen key set get­ting these bolts loose

It’s impor­tant to have a ref­er­ences for “straight” and for “square” and so any mak­er should know what the flat­test and most square things in their shop are for a true ref­er­ence. I don’t have any machin­ist’s squares or a heavy, cast-iron table saw, so I just make do with some alu­minum tools that are pret­ty good. I grabbed the large dry-wall square to use a flat ref­er­ence. Sure enough, there was about an 1/16″ bow in the fence.

Tough to cap­ture with a cell phone cam­era, but both points in the mid­dle are off the straight edge

I placed some scrap pieces on the garage floor and used a 4lb sledge to ham­mer the cen­ter of the fence. Alu­minum is a brit­tle met­al, so I had to go slow. This usu­al­ly mean 1–2 firm whacks and then check to see if it was lev­el. I actu­al­ly went a bit too far, and the fence start­ed rock­ing side-to-side on my straight edge. A cou­ple of whacks on the oth­er side got it right on. I did have to shore up one side as the points near­est the blade weren’t in line any more (or maybe they nev­er were?).

Pre­ci­sion sledge work

This was the most tedious part, but I got it so I could just slide a piece of paper under it. That’s going to be about as accu­rate as I can get using this method I think.

A lot of effort to close a very small gap

The fence is attached with round (or fixed) holes on one side and slot­ted (or adjust­ment) holes on the oth­er. I got the fence placed on one side and then used my alu­minum speed square on the oth­er. This is where a good machin­ist’s square would be used if I owned one, but again — this whole fix is a bit rough any­way, so the speed square is good enough.

Not the ide­al square device

I also noticed that in addi­tion to the “fixed” fence hav­ing been warped, which would have just result­ed in the same issues. So I quick­ly adjust­ed that one too (no sledge ham­mer required).

While tight­en­ing the main fence, I noticed the bolt-on wing was­n’t in line

A quick test cut and I imme­di­ate­ly could tell the piece did­n’t move a bit as soon as the blade cut through. And, just as impor­tant, it was square! (well as sure of square as I can be with my tools!)

  1. Though as it turns out, it had been used to cut some stuff and returned (prob­a­bly by some 2nd rate con­trac­tor), only to be sold as “new” by Home Depot. But it worked fine and I need­ed it for some­thing at the time, so I just lived with it. []

Leave a Reply

Your email address will not be published. Required fields are marked *