Shop Vac Dust Collection

I built an out-board roller sup­port for my dust col­lec­tion for use with my shop vac. For a cheap project made from scraps, I’m very hap­py with the results.

I’ve used the same Ridgid shop vac for dust col­lec­tion for about 16 years. It con­tin­ues to serve me well, but last year I pur­chased a Dustop­per from Home Depot to use with a 5 gal­lon buck­et in order to col­lect saw dust and oth­er debris. This saves on the fil­ter, as most of the dust gets deposit­ed in the buck­et before it actu­al­ly gets to the shop vac. This also makes emp­ty­ing out the waste a lot easier. 

Well, in the­o­ry, any­way. First of all, there are oth­er cyclonic dust col­lec­tors that are for use with shop vacs that no doubt work a bit bet­ter. This was a cheap (around $25) option and it was low­er pro­file (more on that fur­ther down). But it was a huge pain to drag the entire set­up around the garage! The hoses kept com­ing undone. The buck­et han­dle at one point pulled off the buck­et. I tried zip ties and ratch­et straps, but it just wob­bled around and tipped over on me.

A cou­ple of weeks ago I sketched out a rough idea of sup­port­ing the buck­et dust col­lec­tion with anoth­er cast­er. A lot of oth­er DIY’ers solve this prob­lem by mak­ing a ver­ti­cal­ly stack­ing cart, with the dust col­lec­tion on top. How­ev­er, I store my shop vac under my work bench and I need­ed a low pro­file solu­tion. Also, I felt like I could build a min­i­mal sys­tem here and only need to pur­chase a cast­er. I also pur­chased one of those “cut to your own size” shop vac pow­er tool attach­ments, but it end­ed up not being near­ly rigid enough to make a sol­id connection. 

I used some scrap 3/4″ pine ply­wood (like con­struc­tion grade stuff). I mea­sured out the curve of the shop vac body as well as the buck­et and cut that to fit the profile.

I propped it up on some oth­er scraps to check the fit, trim­ming a bit more to fit the curve of the body. I also mea­sured the height from the floor to the bot­tom of the ply­wood (about 4 1/4″).

I cut out some scrap MDF pieces to make a ris­er for the cast­er. The cast­er mea­sures 2 1/4″ tall, so I need­ed about 2″ total. This was two 3/4″ and one 1/2″ thick pieces of MDF, cut down to about 3″ by 3 1/2″. I glued them up and then sand­ed the edges to clean every­thing up a bit. I also sand­ed all the edges of the ply­wood plat­form, think­ing that will reduce shin splin­ters in the future.

• 

• 

I then attached the ris­er to the ply­wood using 1–5/8″ deck­ing screws. I counter-sunk the screw heads on top, just to keep the sur­face flat for the bucket.

As I men­tioned, I used one of those rub­ber, cut-to-fit hose attach­ments. The idea here was that I would nest this into the shop vac attach­ment stor­age slot on one of its cast­ers. Then I could screw the attach­ment to the ply­wood. I real­ly should­n’t have both­ered. The soft rub­ber just did­n’t give me any con­fi­dence that the con­nec­tion was sol­id. And the whole plat­form could wob­ble too much side to side. So, I grabbed a cou­ple of gal­va­nized met­al build­ing clips (basi­cal­ly, a small angle with some pre-drilled holes). I mount­ed those on the under­side of the ply­wood and screwed a 5/8″ screw on each side into the shop vac body. This may result in some lost suc­tion, but I can always go back and seal off those screw holes with some sil­i­con if so. So far, though, I can’t tell any difference.

Last­ly, I took a sec­ond buck­et and just screwed it down to the ply­wood. The dust col­lec­tion buck­et can then nest inside this one. It makes for a very sol­id con­nec­tion that I can pull on, but also allows the dust col­lec­tion buck­et to swiv­el. And, the final test: the entire thing eas­i­ly rolls up under my work bench.

Of course, I prompt­ly pulled the vac­u­um back out to clean up the garage! It works great. And all for the cost of a 2″ swiv­el cast­er. I did blow about $10 dol­lars on that vac­u­um con­nec­tion piece. I may get a more rigid flange con­nec­tion to replace it, though (Wood­craft has one for about $5). I’m con­sid­er­ing also paint­ing the wood pieces gray and black to match the shop vac, which would be an excuse to take it apart and make that con­nec­tion better.