Guitar Effect Test Box

I’m in var­i­ous stages of com­ple­tion for sev­er­al gui­tar effects at the moment and I’ll cer­tain­ly try to write a post for each of those in turn. How­ev­er, I first fig­ured I should post about my gui­tar effect PCB test box I put togeth­er. I by no means first came up with the idea. Paul of DIY Gui­tar Ped­als in Aus­tralia is who I first saw use & rec­om­mend one. In search­ing around for fur­ther ideas, I came across some notes on DIY Stomp Box­es about adding the probe, which can be used in diag­nos­ing PCBs that aren’t work­ing.

A MXR MicroAmp cir­cuit hooked up to the test box

As you can see, I went with a fair­ly large enclo­sure for this project. As it’s real­ly just the off-board wiring stan­dard to most any ped­al project, with no cir­cuit board, this is some­what a waste of space. How­ev­er, I want­ed to leave a bit of space for poten­tial­ly adding some more fea­tures at some point in the future1. This is a pow­der-coat­ed, alu­minum enclo­sure which is not at all nec­es­sary for this, as the wiring is out­side so the met­al box isn’t shield­ing any­thing. So the enclo­sure was a bit of a splurge. But as Mam­moth cur­rent­ly sells these 1590BB enclo­sures pow­der coat­ed for under $10, it’s not exact­ly a bank-buster. The entire test box is less than $25, and many of the parts I already had in my parts bin.

I cut up some cheap alli­ga­tor clips I bought off of Amazon.com to use for the con­nec­tors. They have lit­tle cov­ers over the clips, so they work quite well even when con­nect­ing into close­ly spaced wiring leads. I did knot these just inside the box to pro­vide some strain relief (though it’s not as though this thing is get­ting roughed up much). I used a Mam­moth Elec­tron­ics bypass wiring board just to sim­pli­fy things a bit. I tend to use a stan­dard wiring col­ors for all my projects: red for 9v, black for ground, green for sig­nal to board, and yel­low for sig­nal back from board.

The spa­cious guts of my test box

The one trick my box has is that I added a tog­gle switch to use a test­ing probe. This switch basi­cal­ly hi-jacks the sig­nal return (yel­low) and con­nects the probe (white) direct­ly to the box out­put jack. So if sig­nal isn’t com­ing back from the cir­cuit, I can flip this switch and then use the probe (which is noth­ing more than a 1μf capac­i­tor) to touch along the cir­cuit to trace where the fault is. It’s very sim­ple but incred­i­bly help­ful.

So to quote Paul of DY Gui­tar Effects, if you’re going to even build just more than a cou­ple of gui­tar effects your­self, you’re going to want to build some­thing like this. It’s so invalu­able to be able to test your PCB as soon as you get the com­po­nents installed but before you try to com­plete all the off board wiring & stuff­ing it into an enclo­sure. It’s also extreme­ly fun to hook up to a bread­board and test that way!

A Bazz Fuzz bread­board cir­cuit on the test box
My enclo­sure drill pat­tern
Wiring dia­gram for my test box


  1. For exam­ple, I also saw this post where some­one has added in the abil­i­ty to change the volt­age and add a volt­age sag (to sim­u­late a dying bat­tery), which is real­ly cool. []