Hard Shop Lesson

I got a hard les­son deliv­ered today while start­ing a project in the garage this after­noon. I’ll lead in with say­ing that I’m ok (and will heal up fine in a week or so); only a bit rat­tled. Let me start with where my head was (and should­n’t have been) that got me here.

I’ve had on my “To Do” list for 2019 to learn how to make box joints. Well, here we are into Decem­ber and I’ve not even tried it. I had want­ed to spend last Sat­ur­day work­ing on it, but I let the week­end get away with me with Thanks­giv­ing and Christ­mas dec­o­ra­tions (which are fine and I was glad to get the time I had with all my fam­i­ly). This evening, I had a Cub Scout event with my son in which I was respon­si­ble for bring some audio and video equip­ment (i.e., our home AV receiv­er, speak­ers, and disc play­er). That end­ed up tak­ing a lot longer than I had antic­i­pat­ed. But I had an hour to spare so I fig­ured I’d at least get a jump start on my box joint jig, know­ing all day Sun­day (tomor­row) is going to be busy with oth­er things.

And it’s entire­ly worth under­scor­ing here: this is all arbi­trary pres­sure I’ve put on myself. Absolute­ly no one else cares if I fig­ure out how to make box joints ever, let alone today or even this year. But I had con­vinced myself that I need­ed to rush through the hour to get the table saw jig set up.

I picked out my back­ing board and was look­ing for a piece of scrap that approx­i­mate­ly the same thick­ness as my table saw blade kerf (sim­ply put, that’s the width of the cut that the table saw makes and is frac­tion­al­ly wider than the blade itself). My ini­tial plas­tic piece for the jig end­ed up a big loose the back­ing board, so I want­ed to quick­ly try a dif­fer­ent approach. Mind you, the piece I’m try­ing to cut is less than a 1/4″ thick. So I fig­ured, why not start with a thin off cut and just sand it down to the nec­es­sary thick­ness?

My pow­er sander is a com­bi­na­tion of a belt sander and 6″ disc sander. The disc of course will put a twist on any object pushed into it, so a firm grip and just being mind­ful of one side lift­ing and the oth­er push­ing down is impor­tant. I grabbed a long thing piece of scrap and tried sand­ing it on the disc, not think­ing about where my hands would go if (when) it slipped out of my grip. I also failed to put on gloves. You cer­tain­ly do not wear gloves with some pow­er tools (any­thing with a cir­cu­lar spin­ning blade), but they are a good idea with a sander.

The same pow­er sander I have. The disc spins counter-clock­wise. I don’t even have any pho­tos of my own of this pow­er tool!

With­in less than a sec­ond of me push­ing the wood into the disc, it knocked it right out of my hand and left me push­ing my fin­gers into the sand­ing disc. Now, in all the pow­er tools I have, if I had to pick one that I was going to injure myself on, it would prob­a­bly be the pow­er sander. Blades, as you can imag­ine, can quick­ly cut into flesh and cause seri­ous injury or death. I can­not imag­ine sus­tain­ing a life-threat­ing injury on a small pow­er sander like mine (though I’m not say­ing it’s impos­si­ble). But at 3600 rpm, 120 grit sand­pa­per can remove skin and nails quite rapid­ly. Cer­tain­ly faster than my reac­tion time. Before I knew it, my unnec­es­sary rush and lack of think­ing about what I was doing caused me to injure my index and mid­dle fin­gers on my left hand. My mid­dle fin­ger got the skin scraped bad­ly but my index nail is about 1/4″ too short now. And boy howdy is that sen­si­tive skin under there!

Again, it’s noth­ing seri­ous. I was able to turn off the machine and imme­di­ate­ly go treat it myself. My fin­gers are sore but the nail should grow back. Hon­est­ly, it’s the les­son I need­ed to learn. Pow­er tools are not any­thing to be in a rush around. Every action with one requires com­plete focus and atten­tion. I need to always think about how the tool could injure me based on the action the tool makes. Giv­en that I was also using my band saw and table saw today (which, I do take less for grant­ed, to be fair to myself), I’m for­tu­nate that this is the injury I end­ed up with.

As my kids join me in the shop more, I’ve had to teach them lessons about safe­ty. I’ve even had to warn my son about touch­ing that very sand­ing disc until it comes to a com­plete stop (he thought he should stop it spin­ning one day after I’d killed the pow­er). I even recent­ly watched James Hamil­ton’s (aka, Stumpy Nubs) video on injur­ing him­self with an angle grinder and remarked on the need to pay atten­tion when I’m work­ing. I firm­ly believe that the num­ber one most impor­tant piece of safe­ty equip­ment is your brain. Too bad I failed to put that and my gloves on this after­noon. I’ll do my best to take that les­son to heart from now on.

Leave a Reply

Your email address will not be published. Required fields are marked *